Menu
Toggle navigation
Items 0
Cart

2015-2020 Ford F150 4WD BDS 6 inch Suspension Lift Kit | 1532H

2015-2020 F150 4WD BDS 6 inch FOX 2.0 Lift Kit - 2015-2020 F150 4WD BDS 6 inch FOX 2.0 Lift Kit
2015-2020 F150 4WD BDS 6 inch FOX 2.0 Lift Kit
SKU 1532H
0 Review(s)
$2,076.60
0 in stock Ships From Manufacturer in 3-5 Days
Free shipping included
60-day returns on most items
Earn reward points with this purchase
12 Customer Q&A(s)
Write a Review
Write a Review

Customer Question On this 6 inch kit. Is the white F150 sitting on 37s or 35s

Asked by: Truck - 11/13/2025
Customer Answer Those pictures were supplied by BDS for the kit so we don't have exact details on it, but they appear to be 37" tires.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Joel Galaz (11/14/2025)
Submit an answer

Customer Question I see there is an option for a carrier baring drop bracket. I have a 2016 f150 ecoboost 3.5l, supercrew will i need the carrier baring drop bracket??

Asked by: Seth - 6/4/2020
Customer Answer That depends on whether or not your truck has a two-piece driveshaft. If you have a SuperCrew 5.5ft bed truck, then you likely have a one-piece driveshaft and a carrier bearing bracket will not be required. If you have a SuperCrew 6.5ft bed, you likely have a two-piece driveshaft and will need the carrier bearing drop bracket.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (6/4/2020)
Submit an answer

Customer Question I really want a level truck once lifted. No front or rear rake. Any idea what size blocks are used on the Ford photos up top for this BDS lift? Primarily the white or silver trucks?

Asked by: Nick - 3/17/2020
Customer Answer We can't outright guarantee that you'll be 100% dead-level with any suspension lift kit, since a lot of factors are involved in determining stance (especially general wear and tear on the stock leaf packs and front suspension). However, in general, the 4" rear block option will typically get you closer to a dead-level stance. The 5" rear block tends to provide some amount of front rake.
Was this answer helpful?  1 of 1  Found Helpful.
Answer provided by: Jason@Stage3 (3/18/2020)
Submit an answer

Customer Question If i was to buy this setup for my 2015 ford f150 4x4 king ranch, could i run 37s on a 20x12 wheel with a -44 offset without any rubbing issues? And also could i buy the coilovers for it later on?

Asked by: Soham - 9/20/2019
Customer Answer You would likely rub pretty badly with that wheel and tire combination and this kit. The biggest tire we recommend to avoid rubbing is a 35x12.50". You could absolutely purchase BDS's 6" coilovers at a later date.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (9/23/2019)
Submit an answer

Customer Question I have a 2015 f150 non auto 4wd and will this kit fit on my f150 I already ordered this kit and didn’t realize it till now

Asked by: Gar - 7/18/2019
Customer Answer Yep. This kit will work fine on your truck if it's not equipped with the 4Auto system.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (7/23/2019)
Submit an answer

Customer Question This kit won’t except factory 17 or 18 inch wheels, so does that mean no 17s at all or can we use aftermarket 17 wheels? I have 17x9s with a -12mm offset and 4.5 inches of backspace. If this kit won’t except these 17s then will the 4” lift version of this kit work?

Asked by: clf343 - 6/17/2019
Customer Answer Neither BDS nor ourselves have confirmed the fitment of any 17" wheels with this kit. We have also not confirmed any 17" wheel fitment on the 4" kit, either. Both kits require at least an 18" wheel with a maximum backspace of 5" to 5.50" to clear a 12.50" wide tire.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (6/18/2019)
Submit an answer

Customer Question Would it be possible to add the Fox 2.5 Reservoir Coilovers to this kit in the future if I wanted to?

Asked by: Jack - 2/17/2018
Customer Answer Yup. You can always add the BDS Fox 2.5 Coilovers for 6" lifts to this kit down the road, if you want. You'll just replace the kit's strut spacer and your stock coilover assembly with the 2.5s when the time comes.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (2/20/2018)
Submit an answer

Customer Question Does this kit increase the factory turn radius? If so, how much? You carry a lot of lifts from different companies, do any of them do a better job keeping turn radius and geometry close to stock?

Asked by: Bret - 5/31/2017
Customer Answer The lift itself only increases your turn radius by a slight degree because of the way the knuckles are designed. What hurts turn radius more than the lift is the bigger wheel and tire combinations folks tend to throw on. We don't have specific specs for turning radius due to its variability with wheel and tire combinations.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (6/1/2017)
Submit an answer

Customer Question Have 6 inch BDS lift with 5" rear blocks, spacers in front, still has a bit of rake. Could I leave spacers and replace o.e. coilovers with Fox 2.0 set to 1 inch lift and get front level?

Asked by: DC - 8/21/2016
Customer Answer You absolutely could. The only thing you have to keep in mind is that the Fox 2.0s are preset at 2" of ride height out of the box, so you'd need to get the Fox Spanner Wrench to set them to 1" of extra ride height over stock.
Was this answer helpful?  0 of 0  Found Helpful.
Answer provided by: Jason@Stage3 (8/22/2016)
Submit an answer

Customer Question Thanks. I will probably just leave the stock tires for now but in the event I do change the stock tires I may go with the Toyo open country LT285/75R18 (35X11.5R18). Will these fit with the 1.5" spacers?

Asked by: Kurt - 6/21/2016
Customer Answer A 285/75R18 is technically like a 34.8x11.2" tire, but in general, that should clear the knuckles just fine as long as you use 1.50" wheel spacers.
Was this answer helpful?  1 of 1  Found Helpful.
Answer provided by: Jason@Stage3 (6/22/2016)
Submit an answer

Customer Question I know this kit states they the stock 18" wheels cannot be used but is it possible to do so with wheel spacers? And if so what thickness? Would like to know in the event I have to take off my 22x12s for any reason, for instance I have a flat and need to run the stocks for a few days.

Asked by: Kurt - 6/20/2016
Customer Answer It's really going to depend on the tires you're using with your factory wheels, but you could feasibly use a stock wheel in conjunction with a wheel spacer and clear the kit's knuckles. We'd recommend using at least a 1.50" Spacer so that you can avoid trimming your factory studs.
Was this answer helpful?  1 of 1  Found Helpful.
Answer provided by: Jason@Stage3 (6/21/2016)
Submit an answer

Customer Question Do we need to cut? Crossmenber ?

Asked by: guillaume - 7/6/2015
Customer Answer This lift kit does require cutting of the subframe for proper fitment.
Was this answer helpful?  4 of 4  Found Helpful.
Answer provided by: Jason@Stage3 (7/7/2015)
Submit an answer
Have Questions?
Load More
Earn reward points
on this product

Stage 3 Rewards is our free customer loyalty program. Earn points on every order and redeem for cash off your next purchase.

  • 100 bonus points just for signing up ($2 to start)
  • 1 point per dollar spent on every order (2% back)
  • Bonus points for reviews, birthdays, and social shares
  • Redeem for $10, $20, $30, $50, or $100 off coupons
See full program details

WARNING: Cancer and Reproductive Harm

This product can expose you to chemicals including those known to the State of California to cause cancer and birth defects or other reproductive harm.

For more information, visit [www.p65warnings.ca.gov](https://www.p65warnings.ca.gov).

Pick Up Where You Left Off

Similar Products & Categories

Logo